|
SPECIALUTRUSTNINGAR
|
||||||||||||||||
 |
|
ALLMÄNT
|
Transportanläggningar
kan knytas samman med hjälp av maskiner såsom transfereringsutrustningar,
vändskivor, sänkstationer och andra utrustningar som företaget konstruerar,
tillverkar och levererar.
|
||||
|
Conveyors har också tekniska och kommersiella samarbeten med andra företag som kan leverera speciallösningar. |
|||||
 |
|||||
HISS FÖR FLERA NIVÅER
| The multi-level lifts can be used in special applications as high-bay buffers for empty or loaded pallets to increase the flexibility of a line without taking up space at ground level. |  |
| Multi-level
lifts essentially consist of a lifting device and a transfer device. Lifting is achieved almost exclusively by gear motors and chains or racks. The use of gear motors fed through an inverter make it possible to obtain high vertical speeds with adjustable acceleration and deceleration. In the simplest applications where low speed is required 2/8 pole motors are used which guarantee even so correct height positioning. The transfer is obtained with chain or belt conveyors or with powered rollers; all of them driven by dual polarity motors or by motors fed through inverters. |
||||
 |
 |
 |
||
|
||||
 |
Level change lifts are used in System 08 conveyors to transfer pallets from one level to another. They are also used in workstations to move vertically the goods to be processed in more ergonomic positions: in this case scissor-type lifts are preferred. |
CONSTRUCTION FEATURES
|
Level
change lifts essentially consist of a lifting device and a transfer
device.
The use of pneumatic cylinders for vertical transfer is the simplest solution but hydraulic cylinders or gear motors with chains or racks are also used. |
| The
transfer is obtained with chain or belt conveyors or with powered
rollers, all of them driven by two polarity motors or by motors fed
through inverters. A simple transfer is added to this in case it were
necessary to unload the pallet into a right-angles line compared to
the original one. |
 |
 |
 |
 |
|
TRANSFERERINGSANORDNING
 |
Transfers are normally used to connect together two or more System 08 conveyors as an alternative to roller bend or turn tables. Transfers are thus used both for the transfer of pallets from one line to one or two lines at right-angles (single transfer) and for the transfer of pallets between several parallel lines (multiple transfers). |
CONSTRUCTION FEATURES
|
|
| These transfers essentially consist of a lifting device and a transfer device. Lifting is achieved through one or more pneumatic or hydraulic cylinders or by gear motors. Pallet transfer operations are obtained using chain or belt conveyors or powered rollers. |
 |
 |
 |
|
VRIDSTATION
| The
turn tables are used in System 08 conveyors to turn the pallets to
the required angle. In particular, turn tables are used in workstations to turn the pallets bearing the item for processing in the most appropriate position and then to send it, in its original position or otherwise, onto the line again. To make workstations more ergonomic, the turn tables can be mounted on a lift. These can be used both to transfer pallets from one line to another right-angled one and to re-route pallets. |
 |
 |
Rotations
are essentially achieved by a lifting and a rotating device. This lifting can be achieved using pneumatic or hydraulic cylinders or with gear motor. |
|
| Rotation
can be either manual or automatic. Furthermore, it can be continuous, in which case rotation is obtained using gear motors, or with preset angles in which case it is obtained using from 90 to 180 degree rotating cylinders. |
|
|
|
||
SÄNKSTATION FÖR P&F HÄNGTRANSPORTÖRER
|
Drop-sections are used on P & F conveyors to carry out vertical transfers of loads without having to unhook these from the trolleys and in narrow areas as opposed to those necessary for vertical bends. Therefore drop-sections may be used both to transfer loads from one line to another at a different level and for vertical transfer, thus making it possible to carry out machining, loading and unloading operations or dipping in tanks (for treatments or painting). |
CONSTRUCTION FEATURES
|
Drop-sections
essentially consist of a device which moves vertically a section
of the load carrying track. The length of this lowering track varies
according to the load dimensions and the number of trolley-sets
it contains. |
 |
 |
The lowering track is guided every time needed to avoid transversal swinging if loads have to undergo automatic loading or unloading, or have to be dipped into rough liquid or fluid baths. Drop-sections with two parallel lowering tracks are provided when trolleys installed on parallel lines have to be transferred vertically. |
 |
 |
 |
 |
 |
||
|
|
....OCH ANDRA
 |
 |
|
|
|
|
 |
 |
|
|
|
|
 |
 |
 |
||
 |
 |
 |
|